Sign In | Join Free | My vivirlatino.com
vivirlatino.com
Xinfeng grain and oil machinery co., LTD
Home > introction >

Learn together under the centrifugal oil filter cleaning step, each operator must be to understand the

Learn together under the centrifugal oil filter cleaning step, each operator must be to understand the

Contact Now

Learn together under the centrifugal oil filter cleaning step, each operator must be to understand the
FIRST machinery based on their own strengths, with a more powerful force, a broader perspective, more effective measures, more effective way, leading entrepreneurs to launch a new round of wealth storm, FIRST will create a more glorious era, hand in hand Hengtong, you will last a lifetime! ?
Centrifugal oil filter cleaning steps:
A centrifugal oil filter off, disconnect the power.
2 Remove the oil drain plugs pollutant room, and then connect the oil pan with oil until the oil flow have been exhausted (you can press the gas when you put the oil drain plug and accelerate out of the oil), and then re-tighten the input connector block cover.
3 Remove the centrifuge input connector, centrifuge output connector, remove the protective cover centrifuge, remove the belt, while 16 with a wrench unscrew the four screws on the base of the centrifuge, the centrifuge from the body the removed oil pan in place.
4 Remove the bleed plug centrifugal oil filter, and then loaded on the location-specific removal tools, fittings screwed onto the cover, twist 3-4 laps, tighten the nut on the bolt to the roots, while the bolts to the pressure plate, screwed in the end.
5 rotating nut, so that the centrifuge housing sink in the end. Obtained at the end face of the cover 6 is pressed by the small groove in the downward projection of the collar, then removed from the housing in the groove of the collar.
Separate loosen nuts and bolts out, then screwed onto the pipe joints pressure plate, screwed in the end, so that the cover and the contact position. Remove the cover and then manually manually.
7 with a brush to remove surface deposits within the housing, and then wipe clean with a rag to cover.
8 Remove the pressure plate, remove the titanium core portfolio, into the oil pan, use gasoline or kerosene soaked 20 minutes after cleaning and blowing with an air gun.
9 using pressure plate, titanium core portfolio soak time to remove dirt holding chamber front panel, with a rag to wipe dirt holding room and then re-installed (installed seals to prevent Mifengbuyan).
10 with gasoline or kerosene to flush out the dirt inside the impeller, and blowing with an air gun.
? 11 in reverse order to the centrifugal oil filter assembly up and collar when installed, the pipe fitting screwed into the plug hole position, rotation, three to four laps, then bolt screwed into the pressure plate, tighten the nut until the pressure in the end cover until the finally mounted on the collar.
12 Loosen the nuts and bolts and fittings unscrew the screw on the plug.
13 re centrifugal oil filter onto the body, tighten the nut, then the input port and an output port connector joints tightened to the centrifugal oil filter base connector.
14 Plug in the power cord, turn on the power switch, start the gear pump, the system is filled with oil, and rotating valve, regulating the pressure of 0.1 ~ 0.2MPa, check if the seal piping and all local oil spill (if any oil spill , reinstall). Close gear pump, disconnect the power, unplug the power cord.
15 open belt installation window, belts installed, and then re-install the belt cover mounted on the window.
Finally, the centrifugal oil filter cover equipment, centrifuges cover nylon cover cover.
16 next startup, operation in accordance with operating instructions.
17 cleaned once every 10 hours to run. More Consulting Welcome

website: www.oilpressline.com/ www.xfmill.com/

www.oilpressworld.com/

www.soybeanpress.com/

www.peanutoilmill.com/


Product Tags:

oil press

      
China Customized Inflatable Bumper Ball Game Bubble Adult Grass CE supplier

Learn together under the centrifugal oil filter cleaning step, each operator must be to understand the Images

Inquiry Cart 0
Send your message to this supplier
 
From:
Enter your email please.
To: Xinfeng grain and oil machinery co., LTD
Subject:
Message:
Characters Remaining: (0/3000)
 
Inquiry Cart 0